Industrial and Commercial Chain Link Fence Gates and Gate Posts
Our company provides you standard chain link fence gates, gate posts and other accessories products for both single and double swing-type gates for industrial and commercial application.
ICSG-01: Galvanized chain link fabric gate used for railway security.
ICSG-02: Chain link fabric gate with barbed tape on top is used for industrial security.
ICSG-03: Three strands of barbed wires are fixed on the top of the chain link fabric fence.
ICSG-04: Chain link mesh and gate framework installation.
Specification of industrial and commercial steel swing gates:
- Material of gate framework: round and rectangular tubular.
- Coating of gate framework and adjoining fence framework: either zinc-coated steel frames or polymer-coated steel frames.
- Top security: three strands of barbed wire or barbed tape.
Table 1 Gate Frame Members, Dimensions, and Weights
| Gate Fabric Height |
Outside Dimension
in. (mm) |
Minimum Weight
lb/ft (kg/m) |
| 6 ft (1.8 m) or Less |
| Round tubular (steel) |
1.66 (42.2) |
1.83 (2.72) |
| Rectangular tubular (steel) |
2.00 (50.81) |
2.52 (3.75) |
| Over 6 ft (1.8 m) |
| Round tubular (steel) |
1.90 (48.3) |
2.28 (3.39) |
| Rectangular tubular (steel) |
2.00 (50.8) |
2.52 (3.75) |
| Interior Bracing |
| Round pipe (steel) |
1.66 (42.2) |
1.83 (3.39) |
| Rectangular pipe (steel) |
1.50 (38.1) |
1.84 (2.74) |
Table 2 Typical Dimensions and Weight of Gate Posts
| Gate Leaf Width |
Material |
Outside Diameter of Pipe
in. (mm) |
Minimum Weight
lb/ft (kg/m) |
| For Gate Fabric Height of 6 ft (1.8 m) or less |
| Up to and including 4 ft. (1.2 m) |
Steel |
2.375 (60.3) |
3.11 (4.63) |
| Over 4 to 10 ft (1.2 to 3.7 m) |
Steel |
2.875 (73.0) |
4.64 (6.91) |
| Over 10 to 18 ft (3.7 to 5.5 m) |
Steel |
4.000 (101.6) |
6.56 (9.77) |
| For Gate Fabric Height Over 6 ft (1.8 m) |
| Up to and including 6 ft (1.8 m) |
Steel |
2.875 (73.0) |
4.64 (7.04) |
| Over 6 to 12 ft (1.8 to 3.7) |
Steel |
4.000 (101.6) |
6.56 (9.77) |
| Over 12 to 18 ft (3.7 to 5.5 m) |
Steel |
6.625 (168.3) |
18.02 (26.83) |
| Over 18 to 24 ft (5.5 to 7.3 m) |
Steel |
8.625 (219.1) |
27.12 (40.36) |
Gate accessories:
Our company provide you necessary and qualified gate accessories as following:
- Gate hinges we provided has a minimum zinc coating of 1.2 oz/ft2 which permits the gate to swing a full 180°.
- Single gate latch, double gate latch, gate stops and keepers (for each gate leaf over 5 ft wide).
- All gate accessories have a minimum zinc coating of 1.2 oz/ft2.
- All of our gate hardware is of sufficient strength and durability to support the gate and repeated open-close cycles.
Gate assembling:
- Gate frame shall be welded at all corners or assembled with corner fittings.
- For gates assembled with corner fittings, 5/16 in. (7.9 mm) diameter truss rods of the same metal and finish as the gate frames is needed for panels of 5 ft (1.5 m) wide.
- Vertical or horizontal interior bracing of the same metal and finish as the gate frame at maximum intervals of 8 ft is needed if gate leaf chain link fabric's width or height is 8 ft or more.
Top security installing:
- To accommodate the higher height of barbed wire, the end members of the gate frame should be extended in height.
- For barbed wire, three strands of barbed wire shall be uniformly spaced and the top strand is approximately 1 ft above the gate frame, the maximum intervals among barbed wires attached shall be of 8 ft.
- For barbed tape, the minimum height for barbed tape installed at the top of the automatic gate shall be a minimum of 8 ft.
