Double and Single Leaf Gate, Pedestrian Gate of Cricket Enclosure

All of our flat and pitched cricket practice net fencing enclosures provided in design options of cricket practice net fencing enclosure fit the three kinds of gate design below as shown in Table 1.

The gates shall be covered with chain link fabric, as shown in cricket net fencing enclosures, to match the fence. The covering shall be drawn taut and laced with 2.0 mm lacing wire to the outer frame and tied to each internal member.

Gate posts shall be medium quality and be suitable for the enclosure gates of different width from 1000 mm to 3600 mm as specified in table 1 and 2. The footings (baseplates) specification are also shown in table 2.

This is a green coated cricket enclosure with gate on the lateral face.

TDCG-01: Green coated cricket practice net enclosure with gate in lateral face.

Table 1: Details of Gate Configurations and Design
Width range of gate leaf mm	1000-1200	1800	3600
Height range of gate leaf mm	2100	3000-3600	3000-3600
Gate design
Outer frame tube: nominal size (DN)/outside diameter (OD)/wall thickness (t) mm	DN25/33.7/2.6	DN32/42.4/2.6	DN32/42.4/2.6
Inner frame tube: nominal size (DN)/outside diameter (OD)/wall thickness (t) mm	DN20/26.9/2.3	DN25/33.7/2.3	DN25/33.7/2.6
Number of horizontal internal members (not exceeding 1200 mm)	1	2	2
Number of vertical internal members (not exceeding 1200 mm)	0	1	2

Table 2: Gate Post Details and Footings (Baseplates)—Class 1 (Medium Quality)
Width range of gate leaf mm	Nominal size (DN) mm	Quality	Outside diameter (OD) mm	Minimum Wall thickness (t) mm	In-ground footings		Galvanized baseplates for concrete pavement
					Minimum size of concrete footings (where applicable)		Baseplate option for bolting posts to concrete pavement mm	Minimum size masonry anchors
					Diameter mm	Depth mm	Baseplate option for bolting posts to concrete pavement mm	Diameter hole mm	Depth mm
Up to 1200	DN 50	Medium	60.3	3.6	250	750	150 × 150 × 8 4-hole	12	75
Up to 1200	DN 65	Medium	76.1	3.6	300	900	150 × 150 × 8 4-hole	12	75
1300–2400	DN 80	Medium	88.9	4.0	300	1000	200 × 200 × 8 4-hole	16	110
2500–3600	DN 100	Medium	114.3	4.5	400	1100	300 × 300 × 10 4-hole	20	125
2500–3600	DN 100	Medium	114.3	4.5	In-ground concrete footing sizes are designed for firm soil conditions.		Gate post with baseplates only when agreed between purchaser and supplier. To be installed with head clamped to top rail for additional support.

This is a drawing of 3600 mm double leaf gate which specifies the posts, fails, foundation and keepers.

TDCG-02: Typical 3600 mm double leaf gate detail for end of cricket nets.

This is a drawing of 3600 mm single leaf gate which specifies the posts, fails, foundation and keepers.

TDCG-03: Typical 3600 mm single leaf gate detail for end of cricket nets.

This is a drawing of 1000 mm pedestrian gate which specifies the posts, fails, foundation and keepers.

TDCG-04: Typical pedestrian gate details for enclosed cricket nets.

Gates accessories:

Gates shall be fabricated in accordance with the diagrams 2, 3 and 4 shown below.
All joints shall be fully welded joints (staggered welding not permitted). Fillet welds shall be not less than 6 mm, exposed surface width and shall be cleaned by chipping and wire brushing.
Two coats of approved zinc-rich paint shall be applied in accordance with AS/NZS 4680 to any galvanized surface damaged by welding.
The height of the gate shall be in accordance with purchasers requirements (subject to allowance for sufficient minimum ground clearances).
Where clip-type hinges are used, a collar shall be welded to the gate frame to provide a bearing surface for either the top or bottom hinge.
Unless otherwise specified by the purchaser, trip-type catches may be fitted to gates for slam closing.
A drop-bolt made from 16 mm diameter round galvanized plain carbon steel shall be fitted to each double-leaf gate and keepers shall be provided at ground level to hold the gates in both open and closed positions.
The locking shall be by drop-bolts suitable for locking. A galvanized 8 mm chain welded to the handhole may be included if required by the purchaser. Handholes shall be incorporated in the gates so that a lock, can be accessed from either side of the gates. Handholes may be omitted if locking from one side only is required.
For single-leaf gates, a shoot bolt made from 12 mm diameter round galvanized plain carbon steel set into a handhole shall be provided for the attachment of a padlock. Handholes may be omitted if locking from one side only is required.

For your convenient installation and accessible to crickets' chain link fabric net fencing, pipe and design options, please refer to the following articles:

Product List

By Fabric

By Gate

By Accessories & Machine

By Application